Flow Meter Summary

In order to capture the pulse output the serial number will need to be noted, preferably with a picture.

Manufacturer	McCrometer
Models	McMag3000
Type	Magflow
Pulse Interface	Built-in
Programming	Windows PC
Battery Life Claimed	** Caution: Battery life reduces with pulse output enabled.
Support Contact	DavidM@mccrometer.com, PamF@mccrometer.com
Straight Pipe Requirement	3D upstream and 1D downstream.
Pipe Sizes Supported	Saddle mounted: 4 to 12 inches
Technical Manual

Site Assessment

- Note straight pipe requirements

- Note full pipe requirements

- Note a grounding rod must be inserted (6 foot copper)

- Note if installing into plastic pipe then grounding rings must be used on both side of the meter

- Note not to install near electrical noise generated from heavy current power lines going to pumps or motors where possible

Pulse Output Connections

Meter Pulse Output Port

For McMag3000 units ordered prior to Nov-2017 (Green cover):

Pulse output port is the right-hand port as shown, with a 7-pin connector:

For McMag3000 unit ordered after Oct-2017 (White cover):

Pulse output port is the right-hand port, with a 4-pin connector:

Pin 1: is Ground (pulse negative)

Pin 2: is pulse output postive.

Pulse Interface Details

Pulse Output Type: Open-Drain Transistor, Normally Open

Pulse Width: 50ms (not adjustable)

Pulse Cable Options

There are 2 options to connect the McMag3000 to the Wildeye:

a) Use the plug-and-play Wildeye McMag3000 cable and plug into Wildeye plug with a "C" channel (recommended)

b) Use the McCrometer supplied pulse output cable and manually wire into the Wildeye "C" channel

Example Wildeye Plug types with "C" Channels:

MAC Plug

MCCD Plug (C1 Channel)

Wildeye McMag3000 Cable

For McMag3000 units ordered prior to Nov-2017 (Green top), use Wildeye part: ACC-CAB-MCMAG3000

For McMag3000 unit ordered after Nov-2017 (White top), use Wildeye part:

These custom McMag3000 to Wildeye cables will plug directly into any standard wildeye plug with a "C" channel.

Refer to Wildeye plug types with "C" channels above.

McCrometer Pulse Output Cable

For McMag3000 units ordered prior to Nov-2017 (Green top):

Use McCrometer part: 7M-025-OE2, 25’ open end cable

For McMag3000 unit ordered after Nov-2017 (White top):

Use McCrometer part: MC-AGM-25-P, 25’ open end cable

In both cases, the wires need to connect to the Wildeye "C" channel are:

Use OEM Parts for Pulse Connection

For McMag3000 units ordered prior to Nov-2017 (Green top):

Obtain a Series 702: 7-pin Single-ended cordset with straight plug, 2m PUR. You can obtain it either from wildeye enterprise or directly from the manufacturer Binder-USA.

The PUR cable should end in three leads: pink, grey, and yellow as shown into

Obtain a 3.5 mm 4 pos M-12 connector either from wildeye (parts number ACC-CON-M12-4POS-F-3.5mm) or directly from the manufacturer Binder USA, and wire according to "C" channel wiring requirements:

For McMag3000 unit ordered after Nov-2017 (White top):

Obtain a Wildeye ACC-CAB-M12-EXT-F-2M cable with 5 cable cores.

Obtain a 3.5 mm 4 pos M-12 connector either from wildeye (parts number ACC-CON-M12-4POS-F-3.5mm) or directly from the manufacturer Binder USA, and wire according to "C" channel wiring requirements: